Windows Could Not Start Windows无法启动

Windows is annoying, that’s taken as read, but some of us cannot afford to Windows是烦人的，这就是采取为已读，但有些我们不能 switch to a Mac切换到Mac and replace all our proprietary software, while Linux is yet to go mainstream.并取代所有我们的专有软件，而Linux是尚未成为主流。 Maybe one day.也许有一天。 In the meantime we Win users have to occasionally contend with errors like this:在此期间，我们赢得了用户，偶尔与错误是这样的：

Windows could not start because of a computer disk hardware configuration problem. Windows无法启动，因为一个计算机磁盘硬件配置问题。
Could not read from the selected boot disk. 无法读取从选定的开机磁片。 Check boot path and disk hardware. 请检查开机路径和磁盘的硬件。
Please check the Windows documentation about hardware disk configuration and your hardware reference manuals for additional information. 请检查Windows文档有关硬件的磁盘配置和您的硬件参考手册的补充资料。

Told you it was annoying.告诉你，这是恼人。 So, what are you supposed to do if you see an error like this.因此，什么是你假定这样做如果你看到一个错误这样的。 Well, you could try restarting, but that’s unlikely to work, particularly if it really is a hardware failure.那么，您可以尝试重新启动，但是这不大可能的工作，特别是如果真的是一个硬件故障。 Hardware failures happen, but are not very common, much more likely is a configuration problem.硬件故障发生，但不是很常见，更可能是一个配置问题。 According to据 Microsoft微软 , this particularly error can occur because of any of the following: ，这尤其是错误发生原因，是因为任何有关下列各点：

The Default value in the [Boot Loader] section of the Boot.ini file is missing or invalid. 预设值，在[ Boot Loader ]区段的Boot.ini文件丢失或无效。
Windows XP is not installed in the location specified in the Boot.ini file. Windows XP是不是安装在指定的位置在Boot.ini文件中。
The Ntoskrnl.exe file is missing or damaged. Ntoskrnl.exe文件丢失或损坏。
The partition path in the Boot.ini file is not set correctly. 分区路径在Boot.ini文件是设置不正确。
General hardware failure. 一般硬件故障。

Having had a laptop die on me sometime ago and having seen similar errors repeatedly until I figured out the problem, I can vouch for the fact that there can be a dozen other reasons.过一台笔记本电脑模具对我前一段时间看过类似的错误，直到我反复揣摩的问题，我可以担保的事实，可以有十几个其他原因。 For instance, if you a Compaq or HP machine and have tried to restore from the restore disks you’re likely to see this error because the restore will not have installed例如，如果您一康柏或惠普的机器，并试图恢复从恢复磁盘您可能会看到此错误，因为恢复将不会安装 SATA的SATA drivers for your hard disk.司机为您的硬盘上。 But, without a floppy drive you cannot install them at restore.但是，没有一个软盘驱动器，则无法安装他们在恢复。

The fix lies in disabling SATA in the BIOS before your system even gets to try and boot Windows.该修补程序，关键在停用的SATA在BIOS中之前，您的系统，甚至得到尝试和启动Windows 。 This will 99% of the time work, allowing you to get up and running albeit without SATA enabled.这将99 ％的工作时间，让您能够启动和运行，尽管没有的SATA启用。 If you really want to get SATA going, you’ll have to create a如果你真的想获得的SATA去，您就可以创建一个 bootable USB or memory card开机USB或记忆卡 that can carry the SATA drivers.可以随身携带的SATA驱动程序。 Re-enable SATA in the BIOS and boot from the USB.重新启用的SATA在BIOS和开机从USB 。 At the point when you get the chance to hit在这一点，当你得到机会击中 F6适用于F6 to install the SATA drivers and hope for the best.要安装的SATA驱动程序，并希望争取最好的。 Just to confirm, my I did resurrect my laptop, but am yet to take the SATA plunge…只是为了证实，我，我复活我的笔记本电脑，但我尚未采取的SATA投身…